EATON XV200 Mini Panel Operation Instructions

Basic information and product specifications

Core positioning and applicable scenarios

Equipment type: Can be used as an independent HMI device or integrated HMI/PLC device;

Applicable fields: Designed specifically for mechanical and system manufacturing, used for equipment visualization, operation, and control. Other uses require confirmation from the manufacturer;

Product alias: XV200 and MK2 are different names of the same product, with completely identical model parameters.

The equipment is divided into 6 categories based on “display type+interface combination” according to the model version classification, and the core differences are shown in the following table:

Model (XV200 series) Model (MK2 series) Display type Core interface (non electrically isolated)

XV-232-57BAS MK2-232-57BAS monochrome RS232

XV-230-57MPN MK2-230-57MPN monochrome Profibus

XV-230-57CNN MK2-230-57CNN monochrome CAN

XV-252-57MPN MK2-252-57MPN Color RS232+Profibus

XV-252-57CNN MK2-252-57CNN Color RS232+CAN

Key technical parameters

Display system: 5.7-inch QVGA (320 × 240 pixels), visible area of 115 × 86mm; monochrome screen supports 256 grayscale, color screen supports 256 colors; Backlight is 1 × CCFL, with a lifespan of 50000 hours, and software adjustable brightness (100%/80%);

Touch sensor: 4-wire resistive, made of glass and polyester film material, calibrated at the factory;

System configuration: 32-bit RISC processor (200MHz), 32MB DRAM, 1.5MB available FLASH, 100 bytes available NVRAM; Support Type I CF cards (for storing operating systems, programs, and data); Built in CR2032 lithium battery (190mA/h), clock backup life of 10 years after power failure;

Power supply requirements: 24 VDC SELV (safe extra low voltage), allowable voltage range 18.0-31.2 VDC (including ripple), short-term (<100ms) can withstand 35 VDC; Maximum power consumption of 8W, continuous current of 0.35A, starting surge current of 2.0A/2s; Equipped with reverse protection and maintenance free fuses, with no potential isolation;

Protection and physical dimensions: front panel protection level IP65, back panel IP20; Dimensions: 212 (width) × 156 (height) × 55 (depth) mm, installation incision: 198 × 142mm (± 1mm), weight: approximately 0.7kg.

Safety regulations and taboos

Personnel and operational requirements

Qualification requirements: Installation, operation, and maintenance personnel must undergo professional training, be familiar with manuals and relevant safety regulations;

Manual usage: The complete manual must be used, and single page operations are prohibited (to avoid missing safety information);

Prohibited from use: Safety functions that cannot be used for personnel or equipment protection, can only be used for routine control and visualization.

Core safety hazards and preventive measures

Potential hazards prevention measures

Explosion risk (explosive environment) is only applicable to non explosive environments or ATEX Zone 22 areas; Avoid severe impact on equipment; Power off before plugging or unplugging the plug

Electric shock risk (opening cover): Do not open the cover by yourself, as it contains live parts inside

Static electricity damage (electronic components): Before touching the device, ground it to release static electricity; Avoid contact with sensitive components such as interface pins

Data loss (CF card): Only power off and unplug the CF card; Enable card slot locking mechanism; Avoid frequent write operations (limited CF card write cycle)

Condensation short circuit (temperature fluctuation) equipment must not be powered on during condensation; After the temperature changes, it needs to be allowed to stand at room temperature before starting

Touch screen damage (sharp objects) can only be operated with fingers or a dedicated stylus; Wear gloves that are clean and free of sharp particles

Environmental restrictions

Avoid direct sunlight exposure (UV can cause plastic to become brittle and shorten its lifespan);

Prohibit the use of corrosive/abrasive cleaning agents to prevent liquids from entering the equipment.

Installation process and specifications

Installation prerequisites

Environmental requirements: operating temperature 0-50 ℃, storage/transportation temperature -20-60 ℃; Humidity of 10-95% without condensation;

Installation location: inside the control cabinet/control panel, can be installed horizontally/vertically; Ventilation gap ≥ 3cm, away from heat sources (such as transformers) ≥ 15cm;

Installation surface requirements: thickness 2-5mm, flatness ≤ 0.5mm, surface roughness Rz ≤ 120.

Cable and wiring specifications

Cable requirements: All bus interfaces require shielded cables, with the shielding layer connected to the connector housing with low impedance to ensure EMC compliance;

Special interface requirements:

CAN interface: Cable characteristic impedance of 120 Ω, maximum length of 5000m (at 10 Kbit/s), and 120 Ω terminal resistors need to be connected at both ends of the bus;

Profibus interface: Cable characteristic impedance of 150 Ω, maximum length of 1200m (≤ 93.75 Kbit/s), terminal resistors need to be connected at both ends of the bus;

Ethernet interface: shielded twisted pair (STP) is used, cross line is used between equipment, and straight line is used to connect to the switch, with a maximum length of 100m; the Internet needs to be isolated or protected by firewall;

Common requirement: The GND terminals of all bus stations must be interconnected to avoid potential damage to equipment.

Equipment fixation and sealing

Installation steps: Prepare a 198 × 142mm (± 1mm) incision → Install a sealing strip in the groove (with the joint facing downwards, without distortion) → Insert the device from the front → Secure with 8 brackets with threaded pins;

Torque requirement: The maximum tightening torque for the bracket threaded pin is 0.1 Nm to avoid over tightening and damaging the equipment;

IP65 requirement: 8 brackets must be fully installed (2 on the left/right/top/bottom), and the installation of 4 brackets does not meet IP65 protection.

Operation and maintenance

Startup and shutdown

Startup process: Power off and insert the CF card containing the operating system → Lock the card slot → Power on and boot → Complete system settings (such as time and brightness) according to the manual → Install application programs;

Closing process: Confirm no CF card write operation → Power off; Avoid frequent switching (which can shorten backlight life at low temperatures), and prioritize reducing brightness instead of shutting down.

routine maintenance

Touch screen cleaning: Wipe with a clean, soft, and damp cloth. For stubborn stains, spray a small amount of cleaning agent on the cloth (do not directly spray the device);

Touch screen calibration: It has been calibrated at the factory. If there is an abnormal response, it needs to be recalibrated according to the “MN05010007Z-EN” manual;

Battery maintenance: The built-in CR2032 lithium battery is non replaceable and has a lifespan of approximately 10 years;

Maintenance restrictions: Equipment malfunctions can only be reported to the manufacturer or authorized center, and self opening repairs are prohibited.

Common troubleshooting

Possible causes and solutions for the fault phenomenon

The device cannot start and the power is not connected/CF card is not inserted/CF card has no operating system. Check the power cable → Insert CF card with OS → Replace the faulty CF card

Touch screen unresponsive uncalibrated/obstructed by objects/installed too tightly recalibrated → remove obstruction → loosen bracket threaded pin

Display black screen backlight off/backlight fault check visualization software backlight settings → Contact maintenance

When starting, prompt ‘No CF card’. The CF card is not inserted or has poor contact. Power off and reinsert the CF card and lock it

Storage, transportation, and disposal

Storage and transportation

Storage conditions: Meet the requirements of temperature -20~60 ℃, humidity 10-95% without condensation, avoid heavy pressure and severe vibration;

Transportation requirements: Use original factory packaging and inspect the equipment for any transportation damage upon arrival.

Disposal standards

The equipment contains lithium batteries (CR2032) and mercury containing cold cathode tubes (<5mg), which must be disposed of in accordance with relevant national regulations and cannot be discarded at will;

The shell material is halogen-free ABS-PC, and the packaging is made of cardboard and PE film, which can be classified and recycled.

Compliance and Standards

The equipment complies with multiple international standards, including:

Safety standards: UL 60950, IEC/EN 60950;

EMC standards: 2004/108/EC, IEC/EN 61000 series;

Explosion proof standard: ATEX 94/9/EC (Zone 22, Category 3D);

Product standards: EN 50178, IEC/EN 61131-2.